Lenco LED (TWO-PIECE) Switch Kit (Single Actuator)

• Simple, quick, Plug & Play installation
• Instant response
• Built-in retractor
• Self-contained, sealed key pad & solid state control box with waterproof Plug & Play Deutsch connectors
• Backlit key pad for optimum viewing at night
• 2 1/16 hole cut-out size

Lenco LED Indicator (TWO-PIECE) Dual Kit - 12 & 24-Volt - Dual Actuator Systems

• Simple, quick, Plug & Play installation
• Built-in retractor
• Low profile design
• 2 1/16 hole cut-out size

Lenco 16 X 12 in Perfomance Trim Tab Kit - Requires Switch

Lenco’s first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13 feet (4 m) to 40 feet (12.2 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with 1 in (2.5 cm) turned up edges and a 5 degree taper on the inside

Lenco 18 X 14 in Perfomance Trim Tab Kit - Requires Switch

Lenco’s first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13 feet (4 m) to 40 feet (12.2 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with 1 in (2.5 cm) turned up edges and a 5 degree taper on the inside

Lenco 4 x 12 in Standard Finish - Requires Switch

Engineered to fit behind ladders. This unique design gives you all the benefits of a standard tab in an ultra compact design. These kits are updated with 11-gauge stainless steel blades. Boat lengths 14 feet (4.3 m) to 25 feet (7.6 m). Blades are constructed of a stronger 11-gauge laser cut 304 stainless steel and 3/8 in(9.5 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) NEW 11-gauge stainless steel blades with option of standard finish or Electro-Polish finish
• (2) actuators with 6 feet (1.8 m) lead and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• Lower mounting brackets included
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 101 Standard Actuator 2-1/4 (5.715 cm) Stroke: 12-Volt

• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 101 XD Actuator 2-1/4 Stroke (5.715 cm) - 12-Volt

• 12-volt actuator
• 5/16 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 101 XD Actuator 2-1/4 Stroke (5.715 cm) - 12-Volt

• 12-volt actuator
• 3/8 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 101 XDS (Short) Actuator 2-1/4 Stroke (5.715 cm) - 12-Volt

• 12-volt actuator
• 5/16 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 101 XDS (Short) Actuator 2-1/4 Stroke (5.715 cm) - 12-Volt

• 12-volt actuator
• 3/8 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 102 HD/XD Actuator 4-1/4 Stroke (10.795 cm) - 12-Volt

• 12-volt actuator
• 5/16 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 101 Standard Actuator 2-1/4 (5.715 cm) Stroke - 24 Volt

• 24-volt actuator
• 5/16 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 101 XD Actuator 2-1/4 Stroke (5.715 cm) - 24-Volt

• 24-volt actuator
• 5/16 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 101 XD Actuator 2-1/4 Stroke (5.715 cm) - 24-Volt

• 24-volt actuator
• 3/8 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco 12-Volt Aftermarket (BRK) Conversion Kit

Now you don’t have to buy a new boat or an entire new set of trim tabs to get all the advantages of the latest in trim tab technology. Lenco’s high-performance instant response actuators are now available to retro fit any boat equipped with the standard length Bennett hydraulic cylinders."

Bennett Hydraulic-to-Lenco Electric Conversion and Performance Upgrade Kits are designed as a direct replacement for the Bennett hydraulic power unit (HPU) on systems using Bennett 4-ring standard trim tab actuators.

Lenco Upper Mounting Bracket With Gland Seal

• 3 Screw Holes
• 1 Wire Hole

Crastin (3 screw holes, 1 wire hole) 2008 through Current - New Style. Clam shell packaged

Lenco 102 Actuator 4-1/4 Stroke (10.795 cm) - 12-Volt

• 12-volt actuator
• 5/16 in mounting hardware
• 6 feet cable
• Lenco’s ballscrew design is more reliable and twice as powerful compared to typical hydraulics.
• Lenco’s tough

Lenco Delrin Mounting Pin (2 pack)

For 101 & 102 Actuators (1.5) Pack of 2

Lenco 4 x 12 in Electro-Polish

Engineered to fit behind ladders. This unique design gives you all the benefits of a standard tab in an ultra compact design. These kits are updated with 11-gauge stainless steel blades. Boat lengths 14 feet (4.3 m) to 25 feet (7.6 m). Blades are constructed of a stronger 11-gauge laser cut 304 stainless steel and 3/8 in(9.5 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) NEW 11-gauge stainless steel blades with option of standard finish or Electro-Polish finish
• (2) 15057-001 XDS actuators with 6 feet (1.8 m) lead and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• Lower mounting brackets included
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 3 3/4 (9.5 cm) Sacrificial Anode Pack of 2

Zinc Sacrificial Anode w/mounting screw. Pack of 2. Clamshell packaged.

Lenco Airboat Trim Tab Rocker Switch - 12 & 24-Volt - Single Actuator Systems

• Single Rocker Switch
• Plug & Play Deutsch Connector
• 30 non-terminated power leads

Airboat Trim Tab Rocker Switch - 12 & 24-Volt - Single Actuator Systems

• Single Rocker Switch
• Installation hardware included
"

Lenco Hatch Lift Rocker Switch (Single) - 12 & 24-Volt - Single Hatch Lift Application

• Single Rocker Switch
• Plug & Play Deutsch Connector
• 30 non-terminated power leads

Single Rocker Switch for hatch lifts with two 30 in non-terminated power leads. This switch is CE certified and ABYC compliant. It is also 20 amp rated and clam shell packaged.

• Single Rocker Switch
• Installation hardware included
"

Lenco Hatch Lift Rocker Switch (Dual) - 12 & 24-Volt - Dual Hatch Lift Application

• Single Rocker Switch
• Plug & Play Deutsch Connector
• 30 non-terminated power leads

Single Rocker Switch for hatch lifts with two 30 in non-terminated power leads. This switch is CE certified and ABYC compliant. It is also 20 amp rated and clam shell packaged.

• Single Rocker Switch
• Installation hardware included
"

Lenco 9 X 12 in Standard Mount Kit 12v

Everything you need in one box! The Standard trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• Double Rocker Switch
"

Lenco 12inx12in Standard Mount Trim Tab Kit 12v With Pro Control Auto

Pro Control Auto delivers industry-leading auto-levelling for unprecedented precision, control, and comfort on the water.

Standard Mount Trim Tabs-The original Trim Tab design, ideal for center console fishing boats to cuddy cabin cruisers.

Suitable for boat lengths from 16ft (4.9m) - 30ft (9.1m)

• Pro Control Auto Keypad (Connectivity - NMEA 2K, Lenco 2K, Mercury SmartCraft)
• (2) 12 gauge 304 stainless steel standard finish blades
• (2) 11-1/2in SD Pro Actuators with 6ft (1.82m) leads and Deutsch connectors
• (2) 3ft (0.91m) Pro Control actuator power pigtails
• (2) upper mounting brackets with gland seals
• (2) 2ft (0.61m) Micro C Drop Cables
• Lenco 2K backbone kit.

Lenco 12inx12in Edge Mount Trim Tab Kit 12v With Pro Control Assist

Pro Control Assist is the manual control option which features a smart, sleek dial controller, providing a best-in-class user interface.

Edge Mount Trim Tabs-Designed for boat applications where a lower actuator mounting height is desirable. Actuator mounts at the trailing edge of the blade giving it a 3 (7.6 cm) lower mounting height on 12 in (30.5 cm) long blades. All

Lenco 12inx12in Edge Mount Trim Tab Kit 12v With Pro Control Auto

Pro Control Auto delivers industry-leading auto-levelling for unprecedented precision, control, and comfort on the water.

Edge Mount Trim Tabs-Designed for boat applications where a lower actuator mounting height is desirable. Actuator mounts at the trailing edge of the blade giving it a 3 (7.6 cm) lower mounting height on 12 in (30.5 cm) long blades. All

Lenco SD Pro Actuator for Surf Applications 10in Pin to Pin

• Fast, precise, repeatable wake enabled through inductive sensors - within 1% accuracy
• Seamless integration into surf systems, with CAN-based hardware enabling smart actuation
• MFD integration available
• Simple installation and intuitive commissioning
• Expanded Mercury(R) integration, connecting directly with SmartCraft(R), providing improved and superior control logic
• Fault and diagnostic capability with overload protection

Build the ultimate watersports machine with the new SD Pro actuator. The cutting-edge actuator empowers boaters to create precise, repeatable wake. Best-in-class connectivity and total customization deliver an unbeatable user experience in your own image

The key to better wake surfing? Practice and repetition. That’s why the SD Pro is precision engineered to deliver a repeatable wake time after time. Simply dial in your number and get surfing - cutting set-up time to a minimum. And improved response times mean you can tweak things in an instant.

The Lenco team has designed the SD Pro actuator to be easier than ever to install in your wake boats, using CAN communication protocol with no power distribution module (PDM) required. And once it’s installed, it’s there to be relied upon, season after season, with a 5-year warranty as standard.

We know the importance of intelligent, interconnected systems. That’s why the SD Pro is built on new CAN-based hardware, to make integration seamless and simple

Lenco Edge Mount Trim Tab Kits - 12-Volt - 12 X 12 in

Everything you need in one box! The Edge Mount trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 17 feet (5.2 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 1 in (2.5 cm) turned up edges and a 5 degree taper on both sides to the trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• Double Rocker Switch
"

Lenco 12 X 12 in Standard Mount Kit 12v with Double Rocker Switch

Everything you need in one box! The Standard trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• Double Rocker Switch
"

Lenco 9 X 12 in Standard Mount Kit 12v with Standard Integrated Switch

Everything you need in one box! The Standard trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• Standard Integrated Switch
"

Lenco 12 X 12 in Standard Mount Kit 12v with Standard Integrated Switch

Everything you need in one box! The Standard trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• Standard Integrated Switch
"

Lenco Edge Mount Trim Tab Kits - 12-Volt - 12 X 12 in with Standard Integrated Switch

Everything you need in one box! The Edge Mount trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 17 feet (5.2 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 1 in (2.5 cm) turned up edges and a 5 degree taper on both sides to the trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• Standard Integrated Switch
"

Lenco 12x12" Edge Mount Trim Tab Kit 12v Electro Polished

All the same features of the Edge Mount series with the addition of Electro-Polished blades. Electro-Polish adds a mirror finish and the ultimate corrosion protection. Actuator mounts at the trailing edge of these 12 in (30.5 cm) blades giving them a 3 in (7.6 cm) lower mounting height. Boat Lengths 14 feet (4.3 m) to 30 feet (9.1 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with a 1 in (2.5 cm) turned up edges and a 5 degree taper on both sides to the trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel Electro-Polished blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 4 x 12 in Limited Space Trim Tabs Electro-Polish Finish

Engineered to fit behind ladders. This unique design gives you all the benefits of a standard tab in an ultra compact design. These kits are updated with 11-gauge stainless steel blades. Boat lengths 14 feet (4.3 m) to 25 feet (7.6 m). Blades are constructed of a stronger 11-gauge laser cut 304 stainless steel and 3/8 in(9.5 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) NEW 11-gauge stainless steel blades with option of standard finish or Electro-Polish finish
• (2) 15054-001 Standard actuators with 6 feet (1.8 m) lead and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• Lower mounting brackets included
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco Standard Integrated Switch Kit - 12 & 24-Volt - Single Actuator Systems

• Simple, quick, Plug & Play installation
• Instant response
• Built-in retractor
• Self-contained key pad with waterproof Plug & Play Deutsch connectors
• Wiring harness length 30 (76.2 cm) from the back of the switch bezel
• 2 1/16 in hole cut-out size

Lenco SD Pro Actuator for Surf Applications 10.5in Pin to Pin

• Fast, precise, repeatable wake enabled through inductive sensors - within 1% accuracy
• Seamless integration into surf systems, with CAN-based hardware enabling smart actuation
• MFD integration available
• Simple installation and intuitive commissioning
• Expanded Mercury(R) integration, connecting directly with SmartCraft(R), providing improved and superior control logic
• Fault and diagnostic capability with overload protection

Build the ultimate watersports machine with the new SD Pro actuator. The cutting-edge actuator empowers boaters to create precise, repeatable wake. Best-in-class connectivity and total customization deliver an unbeatable user experience in your own image

The key to better wake surfing? Practice and repetition. That’s why the SD Pro is precision engineered to deliver a repeatable wake time after time. Simply dial in your number and get surfing - cutting set-up time to a minimum. And improved response times mean you can tweak things in an instant.

The Lenco team has designed the SD Pro actuator to be easier than ever to install in your wake boats, using CAN communication protocol with no power distribution module (PDM) required. And once it’s installed, it’s there to be relied upon, season after season, with a 5-year warranty as standard.

We know the importance of intelligent, interconnected systems. That’s why the SD Pro is built on new CAN-based hardware, to make integration seamless and simple

Lenco SD Pro Actuator for Surf Applications 11.5in Pin to Pin

• Fast, precise, repeatable wake enabled through inductive sensors - within 1% accuracy
• Seamless integration into surf systems, with CAN-based hardware enabling smart actuation
• MFD integration available
• Simple installation and intuitive commissioning
• Expanded Mercury(R) integration, connecting directly with SmartCraft(R), providing improved and superior control logic
• Fault and diagnostic capability with overload protection

Build the ultimate watersports machine with the new SD Pro actuator. The cutting-edge actuator empowers boaters to create precise, repeatable wake. Best-in-class connectivity and total customization deliver an unbeatable user experience in your own image

The key to better wake surfing? Practice and repetition. That’s why the SD Pro is precision engineered to deliver a repeatable wake time after time. Simply dial in your number and get surfing - cutting set-up time to a minimum. And improved response times mean you can tweak things in an instant.

The Lenco team has designed the SD Pro actuator to be easier than ever to install in your wake boats, using CAN communication protocol with no power distribution module (PDM) required. And once it’s installed, it’s there to be relied upon, season after season, with a 5-year warranty as standard.

We know the importance of intelligent, interconnected systems. That’s why the SD Pro is built on new CAN-based hardware, to make integration seamless and simple

Lenco SD Pro Actuator for Surf Applications 12in Pin to Pin

• Fast, precise, repeatable wake enabled through inductive sensors - within 1% accuracy
• Seamless integration into surf systems, with CAN-based hardware enabling smart actuation
• MFD integration available
• Simple installation and intuitive commissioning
• Expanded Mercury(R) integration, connecting directly with SmartCraft(R), providing improved and superior control logic
• Fault and diagnostic capability with overload protection

Build the ultimate watersports machine with the new SD Pro actuator. The cutting-edge actuator empowers boaters to create precise, repeatable wake. Best-in-class connectivity and total customization deliver an unbeatable user experience in your own image

The key to better wake surfing? Practice and repetition. That’s why the SD Pro is precision engineered to deliver a repeatable wake time after time. Simply dial in your number and get surfing - cutting set-up time to a minimum. And improved response times mean you can tweak things in an instant.

The Lenco team has designed the SD Pro actuator to be easier than ever to install in your wake boats, using CAN communication protocol with no power distribution module (PDM) required. And once it’s installed, it’s there to be relied upon, season after season, with a 5-year warranty as standard.

We know the importance of intelligent, interconnected systems. That’s why the SD Pro is built on new CAN-based hardware, to make integration seamless and simple

Lenco 12x12" Edge Mount Trim Tab Kit 12v with LED Integrated Switch

Everything you need in one box! The Edge Mount trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 17 feet (5.2 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 1 in (2.5 cm) turned up edges and a 5 degree taper on both sides to the trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• LED Integrated Switch
"

Lenco 9x14" Airboat Kit without Switch

The world’s first Airboat specific design. The planing surface provides greater lift and less drag. Engineered to prevent the tab from digging in during hard turns resulting in a safer ride. Blade is constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a welded on stainless steel adjustable lower actuator mounting bracket & 1/8 in (3.2 mm) diameter hinge pin. High impact corrosion proof upper mounting bracket with mechanical cable gland seal.

• (1) 12-gauge stainless steel standard finish blade with 2 in (5.1 cm) hinge height
• (1) 15055-001 actuator with 6 feet (1.8 m) lead and Deutsch connector
• (1) 30133-002 actuator extension wiring harness - 14 feet (4.3 m) length
• Lower mounting bracket included
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9x12" Standard Mount Trim tab Kit 12v with LED Integrated Switch

Everything you need in one box! The Standard trim tab kit with the added benefit of having the NEW integrated switch choice & power connector all included. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal. Switch included.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
• LED Integrated Switch
"

Lenco Pro Control Assist Controller Kit

• Day and Night Mode
• Keypad dimensions 2.75in x 4.37in
• 2 1/16in hole cut out size

Pro Control Assist Keypad with programmable memory position recall capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Pro Actuators only

• Pro Control Assist Keypad
• (2) Micro C Drop Cables, 6ft
• (1) Wake Signal Adapter for Non-Mercury Systems
• (2) Micro C Tee Connectors

Lenco LED Integrated Switch Kit (Single)

• Simple, quick, Plug & Play installation
• Instant response
• Built-in retractor
• Low profile key pad design
• Self-contained key pad with waterproof Plug & Play Deutsch connectors
• Wiring harness length 30 (76.2 cm) from the back of the switch bezel
• 2 1/16 in hole cut-out size

Lenco LED Integrated Switch Kit (Dual Actuator)

• Simple, quick, Plug & Play installation
• Instant response
• Built-in retractor
• Self-contained key pad with waterproof Plug & Play Deutsch connectors
• Wiring harness length 30 (76.2 cm) from the back of the switch bezel
• 2 1/16 in hole cut-out size

Lenco Pro Control Auto Controller Kit

• Day and Night Mode
• Keypad dimensions 2.75in x 4.37in
• 2 1/16in holecut out size
• Connectivity - NMEA 2K, Lenco 2K, Mercury SmartCraft

Pro Control Auto Keypad with auto-levelling capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Pro Actuators only.

• Pro Control Auto Keypad
• Pro Control Auto IMU
• (2) Micro C Drop Cables 6ft
• (1) Micro C Drop Cable 15ft
• Wake Signal Adapter for Non-Mercury systems
• (3) Micro C Tee Connectors

Lenco Pro Control Auto Replcement Keypad

Pro Control Auto Keypad with auto-levelling capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Pro Actuators only.

Lenco Pro Control Assist Replcement Keypad

• Day and Night Mode
• Keypad dimensions 2.75in x 4.37in
• 2 1/16in hole cut out size

Pro Control Assist Keypad with programmable memory position recall capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Pro Actuators only.

Lenco Pro Control Auto Flybridge Keypad Kit

• Day and Night Mode
• Keypad dimensions 2.75in x 4.37in
• 2 1/16in hole cut out size

Pro Control flybridge kit for a secondary station set up.

Pro Control Auto Keypad with auto-levelling capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Pro Actuators only.

• Pro Control Auto Flybridge Keypad
• 1.6ft (1.82m) Micro C Drop Cable
• (1) Micro C Tee Connector

Lenco Flybridge LED Key Pad with 20 feet (6.1m) Shielded Harness, Y Connector

Second station LED Key Pad connecting to the NEW (TWO-PIECE) Tactile Switch Kit (part# 15270-001 and/or 15271-001). Add this second station key pad to your NEW (TWO-PIECE) Tactile Switch by plugging into the Y Connector Harness.

• Flybridge Standard Key Pad
• 20 feet Shielded Harness 30097 series
• Y Connector

Lenco 9 X 9 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9 X 12 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9 X 18 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 12 X 12 in Electro-Polish Standard Mount Trim Tab Kit

All the same features of the Standard Mount series with the addition of Electro-Polished blades. Electro-Polish adds a mirror finish and the ultimate corrosion protection. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m). All the same features of the Standard Mount series with the addition of Electro-Polished blades. Electro-Polish adds a mirror finish and the ultimate corrosion protection. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m).

• (2) 12-gauge stainless steel Electro- Polished blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 12x9" Edge Mount Trim Tab Kit 12v Electro Polished

All the same features of the Edge Mount series with the addition of Electro-Polished blades. Electro-Polish adds a mirror finish and the ultimate corrosion protection. Actuator mounts at the trailing edge of these 12 in (30.5 cm) blades giving them a 3 in (7.6 cm) lower mounting height. Boat Lengths 14 feet (4.3 m) to 30 feet (9.1 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with a 1 in (2.5 cm) turned up edges and a 5 degree taper on both sides to the trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel Electro-Polished blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9 X 12 in Electro-Polish Standard Mount Trim Tab Kit

All the same features of the Standard Mount series with the addition of Electro-Polished blades. Electro-Polish adds a mirror finish and the ultimate corrosion protection. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m). All the same features of the Standard Mount series with the addition of Electro-Polished blades. Electro-Polish adds a mirror finish and the ultimate corrosion protection. Boat lengths 16 feet (4.9 m) to 30 feet (9.1 m).

• (2) 12-gauge stainless steel Electro- Polished blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9 X 24 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9 X 30 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9 X 36 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco Pro Control Auto Replacement Flybridge Keypad

• Day and Night Mode
• Keypad dimensions 2.27in x 4.37in
• 2 1/16in hole cut out size

Replacemant Pro Control Auto Keypad with auto-levelling capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Pro Actuators only.

Lenco Pro Control Assist Replacement Flybridge Keypad

• Day and Night Mode
• Keypad dimensions 2.75in x 4.37in
• 2 1/16in hole cut out size.

Replacement Pro Control Assist Flybridge Keypad with programmable memory position recall capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Actuators only.

Lenco 9inx12in Standard Mount Trim Tab Kit 12v With Pro Control Assist

Pro Control Assist is the manual control option which features a smart, sleek dial controller, providing a best-in-class user interface.

Standard Mount Trim Tabs-The original Trim Tab design, ideal for center console fishing boats to cuddy cabin cruisers.

Suitable for boat lengths from 14ft - 18ft

• Pro Control Auto Keypad (Connectivity - NMEA 2K, lenco 2K, Mercury SmallCraft)
• (2) 12 gauge 304 stainless steel standard finish blades
• (2) 11-1/2in SD Pro Actuators with 6ft (1.82m) leads and Deutsch connectors
• (2) 3ft (0.91m) Pro Control actuator power pigtails
• (2) upper mounting brackets with gland seals
• (2) lower mounting brackets
• (2) 2ft (0.61m) Micro C Drop Cables
• Lenco 2K backbone kit.

Lenco 9inx12in Standard Mount Trim Tab Kit 12v With Pro Control Auto

Pro Control Auto delivers industry-leading auto-levelling for unprecedented precision, control, and comfort on the water.

Standard Mount Trim Tabs-The original Trim Tab design, ideal for center console fishing boats to cuddy cabin cruisers.

Suitable for boat lengths from 16ft - 25ft

• Pro Control Auto Keypad (Connectivity - NMEA 2K, Lenco 2K, Mercury SmallCraft)
• (2) 12 gauge 304 stainless steel standard finish blades
• (2) 11 1/2in SD Pro Actuators with 6ft (1.82m) leads and Deutsch connectors
• (2) 3ft (0.9m) Pro Control actuator pigtails
• (2) upper mounting brackets with gland seals
• (2) lower mounting brackets
• (2) 2ft (0.61m) Micro C Drop Cables
• Lenco 2K backbone kit.

Lenco Pro Control Assist Flybridge Keypad Kit

• Keypad - Day and Night Mode
• Keypad dimensions 2.75in x 4.37in
• 2 1/16in hole cut out size

Pro Control Assist flybridge kit for a secondary station set up.

Pro Control Assist Keypad with programmable memory position recall capabilities provides intuitive, precision controls for your trim tab system. CAN communication protocol comes as standard, making integration and installation simple.

Please Note: Pro Control keypads are compatible with SD Pro Actuators only.

• Pro Control Assist Flybridge Keypad
• 1.6ft (1.82m) Micro C Drop Cable
• (1) Micro C Tee Connector

Lenco 12 X 24 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 12 X 12 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 12 X 18 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 12 X 30 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 12 X 36 in Standard Mount Trim Tab Kit - Requires Switch

The series that started the electric revolution! Lencos original Trim Tab design is still the most popular series they build. Ideal for most common style boats from center console fishing boats to cuddy cabin cruisers. Boat lengths 14 feet (4.3 m) to 69 feet (21 m). Blades are constructed of 12 gauge (2.7 mm) laser cut 304 stainless steel with a 5/8 in (1.6 cm) flared trailing edge & 1/8 in (3.2 mm) diameter hinge pin. Upper and lower high impact corrosion proof mounting brackets with mechanical cable gland seal.

• (2) 12-gauge stainless steel standard finish blades
• (2) 15054-001 actuators with 6 feet (1.8 m) leads and Deutsch connectors
• (2) 30133-103 actuator extension wiring harnesses - 20 feet (6.1 m) length
• (2) 15085-001 upper mounting brackets with gland seal
• (2) 50014-001 lower mounting brackets
• Lenco owner’s/installation manual
• Stainless steel mounting hardware
"

Lenco 9 X 9 in Perfomance Trim Tab Kit - Requires Switch

Lenco’s first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13 feet (4 m) to 40 feet (12.2 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with 1 in (2.5 cm) turned up edges and a 5 degree taper on the inside

Lenco 9 X 12 in Perfomance Trim Tab Kit - Requires Switch

Lenco’s first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13 feet (4 m) to 40 feet (12.2 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with 1 in (2.5 cm) turned up edges and a 5 degree taper on the inside

Lenco 12 X 9 in Perfomance Trim Tab Kit - Requires Switch

Lenco’s first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13 feet (4 m) to 40 feet (12.2 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with 1 in (2.5 cm) turned up edges and a 5 degree taper on the inside

Lenco 12 X 12 in Perfomance Trim Tab Kit - Requires Switch

Lenco’s first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13 feet (4 m) to 40 feet (12.2 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with 1 in (2.5 cm) turned up edges and a 5 degree taper on the inside

Lenco 14 X 12 in Perfomance Trim Tab Kit - Requires Switch

Lenco’s first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13 feet (4 m) to 40 feet (12.2 m). Blades are constructed of Electro-Polished 12 gauge (2.7 mm) laser cut 304 stainless steel with 1 in (2.5 cm) turned up edges and a 5 degree taper on the inside